Ball bearing tool
Ball bearing tool
Hey guys,
Who makes that ball bearing removal and installation tool for QM40 engines? I've seen a video of the tool in use, but I can't find it anywhere.
Thanks.
Tim Lampe
Who makes that ball bearing removal and installation tool for QM40 engines? I've seen a video of the tool in use, but I can't find it anywhere.
Thanks.
Tim Lampe
Re: Ball bearing tool
Tim,
Attached is the link to Darrol Cady's site.
Regards Hank D
http://www.darrolcady.com/Accessories/a ... _tools.htm
Attached is the link to Darrol Cady's site.
Regards Hank D
http://www.darrolcady.com/Accessories/a ... _tools.htm
Re: Ball bearing tool
Hi Hank.
Thanks, but that's not the one I was looking for. The one I want has some threaded parts for drawing the bearings in.
Tim
Thanks, but that's not the one I was looking for. The one I want has some threaded parts for drawing the bearings in.
Tim
Re: Ball bearing tool
Tim,
Might want to talk to Shane @ Central Hobbies.
He was talking about one that did not require heat. I have not seen it but that might be the one you are looking for.
Regards Hank
Might want to talk to Shane @ Central Hobbies.
He was talking about one that did not require heat. I have not seen it but that might be the one you are looking for.
Regards Hank
-
- Super Contributor
- Posts: 513
- Joined: Wed Mar 09, 2011 11:44 am
- Location: Paola, KS
- Contact:
Re: Ball bearing tool
I believe the tool in that video is the one that Central hobbies sells, the Triple J fabrication tool.
Out of all the places we could be, this is one of them.
Re: Ball bearing tool
Yep, here it is! I already scoured the Tools section on the Central Hobbies site yesterday but couldn't find it. This time I looked in the Pylon Racing/Accessories section and found it there:fizzwater2 wrote:I believe the tool in that video is the one that Central hobbies sells, the Triple J fabrication tool.
https://www.centralhobbies.com/cat3.php ... subcat=262
Thanks!
Tim
-
- Super Contributor
- Posts: 513
- Joined: Wed Mar 09, 2011 11:44 am
- Location: Paola, KS
- Contact:
Re: Ball bearing tool
If you get one, let us know what you think. I've been tempted to pick one up, too.
Out of all the places we could be, this is one of them.
- airplanescotty
- Super Contributor
- Posts: 700
- Joined: Thu Jan 14, 2010 9:58 am
- Location: Central Florida
-
- Super Contributor
- Posts: 268
- Joined: Wed May 01, 2002 9:28 am
- Location: Calgary, AB, Canada
- Contact:
Re: Ball bearing tool
Tim,
The bearing replacement tool you refer to is made by Jack Hinkel from Arizona. I have this tool set and it works very well. Easy and quick bearing replacement without heating the case.
Randy
The bearing replacement tool you refer to is made by Jack Hinkel from Arizona. I have this tool set and it works very well. Easy and quick bearing replacement without heating the case.
Randy
_____________________________________
http://www.cppra.org/
http://www.cppra.org/
Re: Ball bearing tool
Hi Randy, thanks.RSmith wrote:Tim,
The bearing replacement tool you refer to is made by Jack Hinkel from Arizona. I have this tool set and it works very well. Easy and quick bearing replacement without heating the case.
Randy
Yea, I found it a couple posts back. Its available from Central Hobbies at the link I posted. I'm already friends with Jack Hinkel on Facebook and he's reached out to me there too.
Thanks again!
Tim
Re: Ball bearing tool
Nelson/Jett BEARING TOOL
https://www.centralhobbies.com/cat3.php ... subcat=262
don't forget The quick change Glow Plug Wrench allows you to change out a bad plug in seconds!
Triple J Fabrications/GLOW PLUG WRENCH 10MM
Triple J Fabrications/GLOW PLUG WRENCH 3/8 inch
Triple J Fabrications/GLOW PLUG WRENCH 5/16 inch
https://www.centralhobbies.com/cat3.php ... subcat=262
don't forget The quick change Glow Plug Wrench allows you to change out a bad plug in seconds!
Triple J Fabrications/GLOW PLUG WRENCH 10MM
Triple J Fabrications/GLOW PLUG WRENCH 3/8 inch
Triple J Fabrications/GLOW PLUG WRENCH 5/16 inch
- Attachments
-
- image.php.jpg (85.49 KiB) Viewed 10809 times
-
- 22222.jpg (86.45 KiB) Viewed 10809 times
Re: Ball bearing tool
I got the ball bearing tool and this handy engine stand directly from Jack Hinkle.
I already had the bearings out of my engine before I ordered the tool, but here's a few pics of installing the bearings. Really nice...no stress on the case or pounding the bearings.
Tim Lampe
I already had the bearings out of my engine before I ordered the tool, but here's a few pics of installing the bearings. Really nice...no stress on the case or pounding the bearings.
Tim Lampe
- airplanescotty
- Super Contributor
- Posts: 700
- Joined: Thu Jan 14, 2010 9:58 am
- Location: Central Florida
Re: Ball bearing tool
How do you remove the bearings without heating the case????
QTR ~ Waste Not A Moment!!!!!