Install Servo in Wing - #2 Phoenix

Building and other racing tips and suggestions.
Post Reply
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

This is continuation of the series of build tips on the Phoenix Q500 racer. They are based upon installation in a "Phoenix" that is currently being produced by Jim Lime (eight zero six - 553-5478).

The aileron horns come setup with Allen headed screws that will later be used with ball links.

The final length of the horns (to the top of the ball) needs to be approximately 3/4" above the wing.

A Dremel tool was used to cut the screws to the appropriate length.
Attachments
IMG_7946.JPG
IMG_7947.JPG
IMG_7948.JPG
Last edited by sahartman21 on Sun May 29, 2016 7:04 pm, edited 4 times in total.
Scott Hartman
Fritch, TX 79036
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

The servo will also fit in the rearward section of the radio compartment.

Use a marker to identify the approximate location of the servo.

Use a pin to double check that you will not be cutting through the carbon fiber strips. If it is hard to press through the surface, then relocate the servo.
Attachments
IMG_7950.JPG
IMG_7951.JPG
IMG_7952.JPG
Last edited by sahartman21 on Sun May 29, 2016 3:16 pm, edited 1 time in total.
Scott Hartman
Fritch, TX 79036
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

A hole was cut through the surface of the wing to allow the installation of the servo.

Two 1/8" strips of spruce were glued (with medium CA) under the wing surface.

A slot was cut in front of the servo for the wires.
Attachments
IMG_7958.JPG
IMG_7959.JPG
IMG_7960.JPG
Last edited by sahartman21 on Sun May 29, 2016 3:16 pm, edited 1 time in total.
Scott Hartman
Fritch, TX 79036
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

The following show the installation of the aileron pushrods:
Attachments
IMG_7998.JPG
IMG_8000.JPG
IMG_8001.JPG
IMG_8002.JPG
IMG_8003.JPG
IMG_8004.JPG
Last edited by sahartman21 on Sun May 29, 2016 3:16 pm, edited 1 time in total.
Scott Hartman
Fritch, TX 79036
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

The rods and ball links were removed. Red Threadlocker was applied prior to reassembly.

This will greatly reduce the possibility that they will loosen and come off.
Attachments
IMG_8008.JPG
Last edited by sahartman21 on Thu Jun 02, 2016 6:45 pm, edited 1 time in total.
Scott Hartman
Fritch, TX 79036
sahartman21
Super Contributor
Posts: 597
Joined: Thu Jan 10, 2008 8:52 pm
Location: Fritch, TX 79036

Re: Install Servo in Wing - #2 Phoenix

Post by sahartman21 »

Continue to next post:

viewtopic.php?f=12&t=5387
Scott Hartman
Fritch, TX 79036
Post Reply